The Most Versatile and Adjustable BowQuiver on the Market Today

This is the very same quiver designed by G.Fred Asbell in the early 1980's when he owned and operated Bighorn Bowhunting Co.

After Bighorn Bowhunting Co. was sold 1990 this quiver was discontinued, so in 1993 I purchased all the remaining parts and tooling.

I am now the sole manufacturer and distributor of this quiver.

Price

 

 


The only changes from the original design are as follows:

  • Changed the composition of the foam rubber for the Hood insert.
  • Changed the mounting arm brackets from a formed one-piece construction, to a two-piece construction that is stronger and less likely to fatigue fracture over time.

Infinitely Adjustable For Any Arrow Diameter

 

Unique Features of this Quiver:

  • Adjustable Arrow Gripper Assembly can be adjusted to securely hold any arrow shaft; from the largest aluminum or wood shaft, to the smallest carbon shaft.
  • Arrow Gripper Assembly can be adjusted up or down the Quiver's Center Rod. This allows you to get as much feather clearance as you desire. Also this allows you to balance the Quiver on your bow.
  • Two mounting Arms secure the Quiver to the bow for a solid & stable 2 point mount.
  • Mounting Arms can be adjusted to any center distance required to fit your bow.
  • Quiver can be adjusted up or down on the mounting Arms allowing you to balance the quiver on your bow.
  • The Hood is large enough to accommodate any size Broadhead completely, covering and spacing them so they do not touch.
  • The radius design of the Arrow Gripper and Hood keep the arrows and feathers in a smaller more compact grouping.
  • Square Center Rod keeps all components in line and does not allow them to rotate.
  • Using the standard mounting Arms, places the feather of the arrow back towards the shooter, keeping them inside of the bow's profile. Standard mounting Arms are 1 Short Arm on the top, and 1 Long Arm on the bottom.
  • All Screws used are Stainless Steel.
  • Can be mounted to any Recurve or Compound bow.
  • Securely holds 6 arrows of any size.

Optional Mounting Configurations:

  • You can specify which combination of any two mounting Arms you want.
  • Two Short Arms: this mounting would place the Quiver parallel to the bow's riser with the arrow feathers in front of the lower limb.
  • Two Long Arms, this mounting would place the Quiver parallel to the Riser and back towards the shooter. The arrow & feathers would be mostly inside of the bow's profile.
  • Stabilizer hole mounting arms, wrap around the front of the riser and mount to the stabilizer hole. These brackets can be used in pairs or with either of the other mounting brackets. Also they can be customized by bending/twisting them to fit under the limb bolts on T/D recurves.

If you have any questions call 303-750-8398

Complete Quiver Assembly $49.95
Arrow Gripper Assembly $28.00
Foam Rubber Hood Insert $4.00
Quiver Hood $6.80
Arrow Gripper Rubber $8.00
Arrow Gripper Clamp Bracket $15.00
Arrow Gripper Side Plates $7.60
Short Mounting Arm $4.00
Long Mounting Arm $4.00
Stabilizer hole Mounting Arm $4.00
Mounting Arm Clamp $3.50
Quiver Center Rod $10.00
Misc. Screws (Stainless Steel) $.50 each
Misc. Nuts $.50 each
Shipping and Handling for Quiver: $6.00

All Quiver Assemblies come with two mounting arms of yoiur choice. If for any reason you are not completely satisfied just return the Quiver in
new condition for a full refund - less the shipping charges.

 


Cutting Edge Products, Inc.
7736 N. Carolyn Drive
Castle Rock, CO 80108
(303) 660-6879 phone
(303) 880-0625 Cell phone
Email cut-n-edge@comcast.net


Innovative Products for the Hunter and Outdoor Enthusiast